Automotive World Site

Modification have not finished yet while the alloy wheels not changed. The more thin wall tires, the bigger alloy wheels, higher prestige.

This trend began to depart from the race that is quickly transmitted to the modification spaces. In the circuit, large alloy wheels with tire walls thin (low profile) and the tread width is very beneficial because car drivers become more agile and responsive on the corner.

Moreover, hardly changed the tire diameter, so no longer need to adjust the speedometer and odometer. Large wheels also appear to appear sporty and masculine. No doubt, the main factor driving this is the proliferation of this trend the community.

Changing the default factory alloy wheels (OE / original equipment) with a larger diameter is known as plus-sizing. In these terms then known repertoire of plus-one, meaning that adding one inch diameter alloy wheels from OE. Examples from a 16-inch 15-inch. Similarly plus-two, add two inches, from 15 inch to 17 inch, and so on.

Apparently according to Consumer Reports testing, consumer protection agency in the USA, plus-one proved to yield the greatest benefits in terms of Performance. Plus-two and so on just gives a little extra traction while driving comfort, hydroplaning resistance and traction dropped. Price to pay is also more expensive. So bigger is not always more profitable. Plus-sizing is not recommended for SUVs unless indeed an option from the manufacturer.

Therefore, if you’re satisfied with the handling and comfort driving your car, it would suggest to forget the plus-sizing. Faithful only with OE.

Risk Plus Sizing

If not, start by considering the risk. Tires with big wheels and low profile responsive ride on the road was smooth. Conversely hollow road / rough, the tire is not perfectly capable of damping. Driving so uncomfortable. Therefore the streets in this country still have to ‘understandable’, the most wise if plus-sizing, not too far from the OE tire size.
Not only eroded the level of driving comfort, plus sizing excess (plus two / three or more) also threaten the safety wheels. Consumer Reports Tests at plus-three plus two and end up with damage to wheels and tires.

Choosing Velg

If you know the risks, and remain ‘unwilling’ with OE tires, it was time to visit the tire store / modifier. They will offer wheels and tires that fit on OE tires. As a rule, the addition of 1-inch diameter alloy wheels, in the match by lowering the tire wall thickness of between 50-10 percent and the addition of the tire tread width of 10 millimeters. Make sure also speed rating and load rating of the new tires should be higher than the original tires. Please note, plus sizing tire diameters are always changing overalls. It is difficult to exactly match the OE. This will affect many things including the speedometer.

Check also the wheels are in the drill. Most wheels are made of aluminum or a mixture of aluminum and steel. The problem is their quality varies considerably. To check, start by asking how the wheels were made. Alloy forgings (forged wheel) the most powerful and most expensive. Pressure cast wheels are also sufficient, in addition to a stronger alloy wheels are also lighter than the print (cast wheel). This last alloy is made by flowing molten metal into molds.

After that check also his bolt pattern, does not fit with those of your car. So forget about the wheel-pit yearning heart that holes not match. Sellers may offer some kind of adapter that can outsmart the holes that do not fit this. Be careful, this second solution because this adapter will increase the tension in the bolts may loose when driving. Make sure the tires have offset the after-specification cars. Tire tread also peered stretchy whether grind liang ban.

Choosing modifier

Now check modifier that will change the tire. Choose which specialize in plus-sizing. Choosing an incompetent shop tire and wheel damage risk.

Make sure the warranty if not satisfied or no damage as the tire grinding wheel or speedometer screw hole.

Workshop is also equipped with a wheel aligned to prevent early tire wear. Similarly, the ability to adjust suspension system that must adapt to new legs

For motorists who drive a car with a Multi Information Display (MID) device can easily monitor the use of fuel. Then, how about the MID figures show that wasteful fuel usage? Least wasteful fuel consumption also depends on driving style, technical factors other than mechanical course.

Here are some tips and tricks that need to be done to reduce fuel budget:

1. Do not stomping.
   Pedal must be stable and gradual. If you step on the gas pedal abruptly, auto fuel that will be sucked into the combustion chamber is also growing. Meanwhile, at that time was still low engine rpm. Consequently not all that fuel into the engine room fire. Which is called a waste. Because no fuel coming out in the form of energy, but go wasted through exhaust.
2. Discover the engine RPM.
   One way to make an efficient fuel consumption is to change gear (transmission) the right, which is when the engine reaches maximum torque (maximum moment).Gearshift when cars were in need of torque (thrust force), should be conducted with respect to information about the maximum moment (maximum torque) of each car (usually in units of kgm / rpm). Meanwhile, if the vehicle is moving (where the thrust is not needed), the most efficient when driving with the RPM between 2500 until 3500 and with the highest gear.

   For example, technical data on the manual written book Maximum torque: 200Nm/3750rpm. This means that the highest moment of 200Nm occurs at the time of rotating machines as much as 3750 per minute.

   In this example, means that we should make the shift gear when the figure shows the range of 3750 rpm. Figures can be viewed at RPM tachometer located on the dashboard of a car.

   Figures RPM on tachometer very important note. To streamline fuel consumption, while speeding down the road. Keep the engine speed at the maximum torque range. Because, that’s when fuel supply is in accordance with the output from the machine.

   One habit that is often overlooked driver is: do not immediately adjust the gears after lowering speed (deceleration). After running hard and then suddenly put the brakes suddenly, you should also pass the shift gear to a lower position.

3. Measure the HC and CO.
   Whether or not extravagant consumption of fuel is also determined by engine components. Machine components that have a lot of wear / damage can cause incomplete combustion processes.To detect it, check the exhaust emissions. If the examination results show the value of HC (hydrocarbon) and CO (carbon monoxide) is too high, this is a sign of combustion in combustion chamber is not perfect (lots of wasted fuel).
4. Expenses and Activator.
   Another factor that determines the fuel consumption is a load and drive (drive vehicles). Increasingly heavy burden to be transported, their consumption will also increase. The definition of driving include: couplings, bearings (wheel), coupling (propeller shaft), axles, and wheels.

   When these components worn or damaged, would cause loss of power generated by the engine to push the car running. Meanwhile, fuel consumption remains large. Related to the wheels, use of large tires and wheels, including the factors that affect fuel consumption.

Here, other tips are also noteworthy:

1. Habits out of the office lunch / evening, preferably reduced. Bring lunch / delivery seemed better.
2. If traveling, take the family / colleagues that one purpose / intention to go together in one car. For the same matters do not necessarily have to run two or three vehicles while with one unit will suffice.
3. Switch to public transport such as busways, railway, or metrominis.
4. When a traffic jam, while out of town, you should stop first. Changing other activities such as rest, eat, go to the bathroom, or fill the fuel to decompose congestion.
5. Drive gently. Reduce the frequency of braking. When facing a red light does not need to step on the gas, let the car slide because they must be stopped. Reduce the frequency stepping on the gas and brakes. This is the step energy disposal in vain.
6. When sliding or decreased, gear should not be positioned at neutral. Engine brake effect proved more economical fuel than stationary.
7. Turn on the AC as needed.
8. Ask workshop setting appropriate timing according to the type of fuel used. Ignition point too forward or backward resulting wasteful of fuel.
9. Clean the air filters (can be done by yourself) per 2500 km, or depending on conditions.
10. Do not heat the car for too long, maximum 2 minutes. Warming-up machine for 30 minutes, synonymous with traffic for 30 minutes as well.
11. Find the route / alternative road is not jammed, out a little with the current path is more save.

For the users of motor vehicles, the brake function is essential and not negotiable. Brakes are the most important safety component for the needs of motorists. For that, the condition of the brakes must always work perfectly, so that we avoid the incident “brake relieved” that eventually makes disastrous. Maintaining and improving the brakes are actually more modest than the engine or electrical system. There are several things that need to be taken by the driver to brake the car working properly:

1. Brake shoe or brake.
   To know the condition of the brake lining can be done by running the car at low speed while pressing the brake pedal and a half. Open the window and pay close attention friction voice. Both cars use the system disc brakes (disc) or drums will be issued a metal scraping sound when the brake has been exhausted. When that happens, replace the brake immediately with new products that manufacturers are encouraged to get maximum braking. Because, when the brake is still left plugged up, can cause abrasion on the wall above the disc or drum. If you already eroded, of course, costs will be far more expensive.
2. Tromol (drums).
   Currently there are many cars that use tromol or drum brake system. When rarely cleaned, much less often through a puddle of water, be easy on the brakes Tromol rusting. Immediately clean the rust that is on the dust cover (the dust cover) with fine sandpaper. Clean up all traces of rust remaining on the brake with the same sandpaper. Then coat of lubricant on the parts that have friction. Be careful when installing the brake circuit back or ask for your trust to do this workshop. When you are replacing it, try to walk slowly to reexamine the accuracy of the brake job.
3. Erosion of discs and drums.
   When abrasion disc or drum already occurred due to brake that has been discharged, you can bring your car to the turner. Just need to considered thoroughly to determine if it needs new turner returned or replaced. Measurement error on turning could be fatal, because the brakes may not work optimally.
4. Brake fluid.
   Brake fluid is like the heart of the braking system. For that volume of brake fluid in the master brake should always be on a level that is determined. To determine the appropriate amount of brake fluid, can be seen at the height of the control line in the brake fluid bottle.
5. Master brake.
   Braking system or not less than the maximum grip could result from the ineffectiveness of the master brake performance. Usually caused by brake fluid pressure in the brake master reduced. To restore these pressures can be achieved by rearranging the wind pressure in the brake master. For that, prepare to open the bolt wrenches his master cylinders. Before the bolts are opened, ask your partner to help shake up the brake pedal. When stepping repeatedly on the brake pedal under, ask your partner to hold some ground, while you loosen the master cylinder bolts. In this way the brake fluid will shine and you must immediately mengencangkannya bolt it back quickly. Ask your friend to repeat a foothold on the brake pedal. If the footing at the end was not too deep, then the improvement you make is correct.
6. Handbrake.
   Perform inspections on handbrake cable (handbrake). In serrations handbrake, you can moisten it with lubricating gel or grease (fat). While the cord itself can be smeared with lubricating oil. Check the length of the cord level through Handbrake lever. If the pull is too high, you can reduce it through bolts controller. Handbrake lever repeatedly for lubricants and lubricant gel evenly. When you pull the lever handbrake has been short, but still less good grip on the brake, it means that the brake was thirsty and asked to be replaced.

Have you ever bothered with the appearance of strange noises from under your car? Of course very annoying and not make a bad mood? Usually, the noise is experienced by an old car over five years. The solution, take it to the mechanic and the mechanic will resolve the dispute. It’s easy,  isn’t it?

But for car owners who want to know the source of the sound before taking it to the shop, not to impress ‘fooled’ by the workshop, here are some parts that need to be checked to make sure:

1. Arm Bushing
   Characteristic sounds produced in this section is repeated loud squealing noise, especially when the wheels through a bumpy road. It’s a sign that the rubber is brittle aka no longer flexible and should be replaced with new ones.
2. Ball Joint
   The sound is heard in this section is when the tire up to a maximum deflected to the left or right, you will hear the sound of clashing metal. Handling can be given a fat / grease on the part, or replaced with new ones.
3. Bushing / Strut-Bar
   The voice is heard in this section is accompanied by the sound of clashing metal voice squeaking at the bottom of the front seat, which is more subtle than the sound of screeching at no. 1. The reason is the rubber strut-bar is brittle or broken. Replace with new ones immediately.
4. Bearing or ball bearing
   Characteristic buzzing sound is generated, a sign that the bearing is cracked or broken. If not promptly replaced, ball bearing wheels can come loose and it will be difficult to spin. The reason is the fat or oil has run out or damaged roads often pass in a high speed.
5. Stabilizer Link
   Voice ‘duk-duk’ smooth, both in front and behind, which arises because the rubber that has been broken. The cause is often passing in high-speed roads. Immediately replace with new rubber.
6. Tie-Rod Long
   The voice that arises also in the form ‘duk-duk’ fine underneath the front car, while car running. This is due to grease on the connection has been depleted and needs recharging.
7. Per Leaf Rear
   Screeching sound comes from this part dry and rusted. Overcome this problem by smearing each leaf with a lubricant or oil, or also slipped pieces of rubber inner tube between the plates per.
8. Shockbreaker
   Beep ‘jedhug’ will sound if the vehicle passing through a hole in a high speed. We felt it would also slashes hard, especially on the shockbreaker the dead.

How much of our attention on the vehicle that we use every day? Often we ignore regular maintenance on our cars so that its condition remains excellent. Maybe this is trivial, but if not carried out could cause a bigger problem and requires expensive repair costs.

Car components have an age or lifetime and it can be extended with an easy and inexpensive maintenance. Here are the steps that can be done to prevent damage before their time.

1. Before you turn off the engine, reduce the volume and turn off the vehicle’s audio system. With the machine shut off the audio before, at least the audio system does not store electricity. If the remains are still stored electrical current, voltage spikes occur is feared that resulted in an audio system become damaged.
2. Straighten your car tires when parking before the machine off. In quiet conditions and wheel deflected, then the engine rpm will go up if the car back is turned. Because, power steering designed to work in a state is not straight. When the steering wheel straight, the engine will reach the round of stationary and power steering are not working fully. Thus, power steering components including the oil will remain durable.
3. Turn off air conditioner before the engine is turned off first. This allows bearings or wheel bearings and some components of the AC compressor will live long. Therefore, these components do not stop abruptly when its round was high.
4. For turbo-engined car, leave the engine to shut down for a moment before. When stationary engines, bearings or bearing lubrication flow turbo in a stable condition. So that conditions would be more durable bearings considering the performance is strongly influenced bearing turbo.
5. Check tire pressure frequently. Lack of wind pressure can make the surface uneven tire wear. To be more perfect, you should do periodically tire rotation every 10,000 km or six months.
6. Prevent windshield when the car parked in the blistering. You can use cardboard, newspaper, or cloth to cover the windshield so that ultraviolet rays from the sun does not enter into the cabin. UV rays can fade fabrics made of foam seat cushions and become brittle.
7. Avoid high-speed hit the hole. If it is too often forced, the age of suspension and tires will be broken.
8. Do not let the engine speed is too high. When you transmit your car manual, gear position to immediately move the lower positions. In addition to keeping the engine does not overheat and remain durable, as well as fuel consumption becomes more economical.
9. Perform routine inspections according to the official repair shop service manual. Make sure the condition of air filters, radiators, spark plugs, battery until the water in perfect condition.
10. Always use engine oil derived from synthetic raw materials that are specifically formulated with high quality additives, so it can provide better benefits than mineral lubricating oil. The oil was shown to increase resistance to heat engines, reducing the friction between the engine and stabilize the rate of oxidation.
    For diesel-engined car, use oils that contain high-tech additives capable of controlling the oxidation and control of soot  well, thus providing effective protection against piston deposit formation as a result of high temperature, wear and tear, corrosion and foaming. Thus, your machine will be maintained in a durable.