Perhaps you are one of a very busy person, a task force to frequently travel outside the city or the country in the long term. If you have a private car, it should be noted that when returned later, the vehicle is not in the condition of abandoned or tragic. The first step you should do is to wash the car before abandonment. Then, follow these tips:
1. The position of the handbrake released
If left in a state of emergency brake in, especially for a prolonged period, will occur adhesiveness between oil disc brakes, especially for vehicles that have Tromol the rear wheels. One additional thing, it is better you leave the car keys depending on your vehicle’s steering wheel. If your house has a maid, this will be very useful for heating a vehicle every day. But do not leave your car keys if it does not have a garage or out in the open.
2. Wiper with foam padding or logs
When kept in contact with the windshield, wiper rubber will slowly harden and no longer pliable. As a result, these rubber (commonly called dead rubber) will be rough in the future be used to wash your windshield.
3. Try all four tires in the state were raised, does not stick to the floor
Way, simply by using a jack and a stand-jack. The intent was awake and not a car suspension is burdened by heavy vehicles. A car that is never used in a long time suspension will usually go up and down, so that when used later, the car will feel uncomfortable.
4. Remove the battery if the car is more than two weeks left
Why? The reason is because car batteries are very sensitive. When the vehicle was not turned on at all in two weeks or more (especially when you leave home there are no helpers), it will affect the battery, which can be damaged faster than the vehicle is used daily.
5. When the parking lot side, chock your tires with four beams
This applies to those that have a garage with a sloping surface. In the first tips that are not mentioned either enter a position if the vehicle handbrake was left long enough, but how if the surface is tilted? It is easy, simply chock all four tires with blocks or other hard object so that the car has not changed position.
6. Put fragrances, cars, and cars with a cover cap
Fragrances, serves to neutralize the musty odor that may arise because the space in a closed car in a long time. In addition, cars that are left in the open state also allows dust particles to enter the car through the cracks, which it certainly is not desired by any car owner. To avoid it, just buy an ordinary car covers are sold in car accessory shops.
This means that drivers no longer have tired of stepping on the clutch to shift gears. On cars with manual transmission, to shift gears, the clutch must be pressed.
Another fact, of all the control systems should be operated driver’s car, the clutch is the most energy-consuming. In addition, the level of operation is also very high, especially when traffic jams or solid creep!
Easy out
Nevertheless, it turns out there are still many among us who still assume negative effect on the automatic transmission. It is also recognized by auto manufacturers. For example, if the strike, cars with automatic transmission can not be encouraged. If is often used in mountainous areas, brake quickly exhausted.
All the assumptions of the past. Now, more and more automatic transmission, the manufacturer provides the mechanics who have the ability to fix it faster if there is a problem. In fact, now there is also a general workshops that could deplete the entire automatic transmission fluid (ATF) in the transmission and then filled with a lubricant that really new and clean.
In the car now, especially the use of injection systems, when the battery is weak, then the machine will not start. Because the engine computer to get energy from the battery. Therefore, the position of manual and automatic transmissions the same!
Then, on the assumption that the automatic braking when the car drove lavishly in areas with many derivatives, ascertained, that the condition occurred because the driver was too relaxed, allowing the transmission to position “D” course. In fact, D is the highest gear.
Keep working
To reduce the workload of the brakes, the driver must use engine brake effect by using a lower gear. In this case, it could be “two” or if more steep and slippery, should be “L”. Same with low teeth, 3 or 2 on the manual transmission. As for acceleration, the driver should kick or step on the gas pedal down fast!
So, driving with automatic transmission that does not mean the hand does not work at all. At a certain field conditions, 3, 2, and L should be used. Hand still be active. Only the left foot is completely relaxed. No need to stampede the clutch at all. For example when the streets are declining or accelerated during the ascent!
In fact, the bad conditions, by releasing the brake pedal and transmission at the position “D”, the car can crawl without having to hit the brakes.
If you already taste the delicious automatic transmission, especially for those who drive themselves, often through a traffic jam, and have high mobility, they certainly will not want to go back to manual if you do not have to. In fact, they are willing to spend additional costs, both for the transmission of more expensive fuel consumption plus a little more than manual
Rain and intense heat usually become the main enemy of rubbers in the car.
Components that include rubber wiper, doors, hood, glass edging, and much more. When it comes to neglected,the potential becomes painfully annoying when driving.
In order elasticity and suppleness awake, spray containing silicone fluid, at least once a month.
Follow these steps to maintain.
• Prepare tools and equipment such as wet and dry cloth, brush, moisturizing liquids containing silicone rubber.
• Clean the surface first and the surrounding rubber.
• Besides the cloth, use a brush to clean the dust that was still attached.
• Spray containing silicone rubber all over evenly.
• Another way is to spray into the sponge. Next apply a liquid rubber component was washed over the target.
• Allow for a moment and make sure the liquid is absorbed into the rubber.
• The rubber components are ready to appear fresher.
Remember, this step is a component of prevention in order to function until the rubber was not damaged. The steps above do not apply for a broken rubber.
For motorists who drive a car with a Multi Information Display (MID) device can easily monitor the use of fuel. Then, how about the MID figures show that wasteful fuel usage? Least wasteful fuel consumption also depends on driving style, technical factors other than mechanical course.
Here are some tips and tricks that need to be done to reduce fuel budget:
- Do not stomping.
Pedal must be stable and gradual. If you step on the gas pedal abruptly, auto fuel that will be sucked into the combustion chamber is also growing. Meanwhile, at that time was still low engine rpm. Consequently not all that fuel into the engine room fire. Which is called a waste. Because no fuel coming out in the form of energy, but go wasted through exhaust.
- Discover the engine RPM.
One way to make an efficient fuel consumption is to change gear (transmission) the right, which is when the engine reaches maximum torque (maximum moment).Gearshift when cars were in need of torque (thrust force), should be conducted with respect to information about the maximum moment (maximum torque) of each car (usually in units of kgm / rpm). Meanwhile, if the vehicle is moving (where the thrust is not needed), the most efficient when driving with the RPM between 2500 until 3500 and with the highest gear.
For example, technical data on the manual written book Maximum torque: 200Nm/3750rpm. This means that the highest moment of 200Nm occurs at the time of rotating machines as much as 3750 per minute.
In this example, means that we should make the shift gear when the figure shows the range of 3750 rpm. Figures can be viewed at RPM tachometer located on the dashboard of a car.
Figures RPM on tachometer very important note. To streamline fuel consumption, while speeding down the road. Keep the engine speed at the maximum torque range. Because, that’s when fuel supply is in accordance with the output from the machine.
One habit that is often overlooked driver is: do not immediately adjust the gears after lowering speed (deceleration). After running hard and then suddenly put the brakes suddenly, you should also pass the shift gear to a lower position.
- Measure the HC and CO.
Whether or not extravagant consumption of fuel is also determined by engine components. Machine components that have a lot of wear / damage can cause incomplete combustion processes.To detect it, check the exhaust emissions. If the examination results show the value of HC (hydrocarbon) and CO (carbon monoxide) is too high, this is a sign of combustion in combustion chamber is not perfect (lots of wasted fuel).
- Expenses and Activator.
Another factor that determines the fuel consumption is a load and drive (drive vehicles). Increasingly heavy burden to be transported, their consumption will also increase. The definition of driving include: couplings, bearings (wheel), coupling (propeller shaft), axles, and wheels.
When these components worn or damaged, would cause loss of power generated by the engine to push the car running. Meanwhile, fuel consumption remains large. Related to the wheels, use of large tires and wheels, including the factors that affect fuel consumption.
Here, other tips are also noteworthy:
- Habits out of the office lunch / evening, preferably reduced. Bring lunch / delivery seemed better.
- If traveling, take the family / colleagues that one purpose / intention to go together in one car. For the same matters do not necessarily have to run two or three vehicles while with one unit will suffice.
- Switch to public transport such as busways, railway, or metrominis.
- When a traffic jam, while out of town, you should stop first. Changing other activities such as rest, eat, go to the bathroom, or fill the fuel to decompose congestion.
- Drive gently. Reduce the frequency of braking. When facing a red light does not need to step on the gas, let the car slide because they must be stopped. Reduce the frequency stepping on the gas and brakes. This is the step energy disposal in vain.
- When sliding or decreased, gear should not be positioned at neutral. Engine brake effect proved more economical fuel than stationary.
- Turn on the AC as needed.
- Ask workshop setting appropriate timing according to the type of fuel used. Ignition point too forward or backward resulting wasteful of fuel.
- Clean the air filters (can be done by yourself) per 2500 km, or depending on conditions.
- Do not heat the car for too long, maximum 2 minutes. Warming-up machine for 30 minutes, synonymous with traffic for 30 minutes as well.
- Find the route / alternative road is not jammed, out a little with the current path is more save.
Leaky tire problem is very difficult, especially cars. As we was enjoying the journey, suddenly a flat tire due to hit a nail or similar sharp object. We need to replace a leaking tire with a spare tire, and brought to the workshop to patch it. What is ’suffering’ we end up? The answer is: Yes, because now ’suffering’ that continued into our tires!
What are carried out by a tire? Tires that had been intact now pierced with a skewer tool for your little finger. Tires that had been leaked just the tip of the needle, made hollow like the mouth of the pipe. Wow, we dead been the fate of our car tires. It’s known, since that was patched tubeless tire type alias without tires.
Once punched, the rope corking into the hole fiber strain tire with enough potential to further damage the tire. Starting from the rubber material, woven yarn to woven wire made tear and break apart, so that we become increasingly weak tires. This is the form after the end of our tire patched pay 80-10 thousand silver.
For the first time that the patch might still be able to survive for several weeks or months. But if it is leaking again at the same spot, which certainly could not be corked with a rope’s fibers. Well, is forced to use the inner tube.
With little effort and rubber glue, you can avoid further damage and to extend the age of your tires. Pump up your tires full of air, and turn slowly while watering the surface with water. After the air bubbles visible sign of the hole, circle the leaking area with paint or the like as a marker.
Collapse tires and rinse the area around the hole, and then leaked it with a dry cloth wipe. After drying completely, drop hole with any brand of rubber glue, so that the glue seeps into the hole. Help infiltration into the tire with glue jabbing a pointed object such as a pin or small nail into the hole clean, dry and wait for several minutes.
The final step, pump up the tires filled with air and slowly pour water into the hole that has been patched, to ensure that the hole has patched well. Make filling process, from beginning to end with great care and caution, so you do not need to repeat it if there is a failure.
Some advantages of this model such fillings are:
- Strong and anti-failure. Power glue adhesive or rubber adhesive power is higher than the cohesive power of the rubber itself. So this point becomes more powerful than the others. No part may fall off or bounce, as they only use glue. Moreover, the patched section is a very small hole.
- Does not weaken the tires a bit for the network.
- Not add any mass balancing aka affect balance.
- There will never tire in need throughout the life of the tire. Using tires in increasing costs, complicating the wheel settings, the reliability is lower and the risk of failure is much higher.
- Does not depend on others and tire workers as well as the tools that can be more complicated physical damage tires.
- The condition of the tires remained intact, as if it never had a leaky tire. No damage gum tissue, yarn and tire cord.
So, wants to prove? No harm in trying, right?
